![]() The nendo might be better or the same, who the hell cares? I honestly just like the all black case design. So FFS don't go thinking these could be replicated in any fashion for your ride. ![]() The disclaimer i'd leave is this is MY setup and obviously these will change with anyone elses. So at least the 4k passed my test for what I needed it for. This small temperate variation had no affect on overall output. Average coil temperature was right at 115-124 degrees each burp. My friend has a pair of Skar IVX 12' and I think they sound pretty good, albeit I am a newbie when it comes to car stereos, and I havent been exposed to many good aftermarket systems, and they are on sale for 70 right now. Test was done inside a garage so temperature wouldn't be affecting and also checked the temperature of the subs between each burp and never tested if the coils were over 140F. Scoring was done on a average of 5 burps on 4 18" Obsidian's with charging done between each burp. These tests were performed 1 after the other with the nendo going first and a xs power 1005 topping off the batts before each burp. My tests were at 1ohm final load with a mechman elite on 3 batts with the ct4k scoring a 147.2 and the nendo scoring a 146.6. I personally was able to put up my ct4k against a crescendo 5500 head to head in my truck and the ct4k edged over the nendo by a tiny margin. not an amp I see owning very long.Have a bad run in with Coleman or something? lol Car audio amplifier with 2000 watts RMS power at 1-ohm load (14.4v) 1200 watts RMS at 2-ohm load (14. It put out good clean power, but **** 1 time going into protect and completely fried. I don't know if I even want to get it repaired as it would cost a lot and its not that great of quality. This is partially to inform people of CT's crap protection but also would like to know what you would do. 09 Sienna Subs : Four Team Ascendant 18s.Sub amp: Two Taramps 15k Headunit: Pioneer 80PRS.Mids/Highs two pioneer gm 8604 bridged, one at 4 ohms bridged one at 2 ohms bridged, one ppi 600.2 for tweets. TOP SELLING MONOBLOCK AMPLIFIERS CT-2000.1D // 2000 Watts RMS Monoblock Car Audio Amplifier 5.0 239.99 Shop Now CT-1500.1D // 1500 Watts RMS Monoblock Car Audio Amplifier 5.0 199.99 Shop Now CT-1000.1D // 1000 Watts RMS Monoblock Car Audio Amplifier 5.0 159.99 Shop Now CT-700.1D // 700 Watts RMS Monoblock Car Audio Amplifier 5.0 139.99 Shop. These higher quality amps are Orion, DC and Mmats. ![]() Every other amp that I have owned that this amp was supposed to match in quality would go into protect, then power up after as the protection circuit wasn't a complete POS. Either way I need to know what to do, and will never spend money on CT again. I thought the point of the protection was to protect it before it was damaged, not allow it to further damage itself. I don't really understand the point in having a worthless protection circuit. Ive been looking at the ppi 1000.1 sonic tested it at 938 2ohm 11621 ohm so at least I know it does rated power. Anyone have any idea how much it would cost to fix, or how much it is worth blown? 138 amp has pretty much everything need 600rms at 2 ohm (for sub I have now) 750 1ohm (if I get another d2 sub later) but I know nothing about these at all. This is partially to inform people of CT's crap protection but also would like to know what you would do. My dealer told me that they are a new model from previous but didnt get to talk much about them. Paul Kim at M & Tech probably wants his money back cthedinger, why dont you come try to lie your way out of. So much for the lie that you made 'mistakes' He never paid back the 250,000 he stiffed a supplier out of. I was basically trying to find out if anyone knew of the changes made. So apparently Coleman is still pulling the same as 4-5 years ago. Just people who have them and people who trash talk it. Every other amp that I have owned that this amp was supposed to match in quality would go into protect, then power up after as the protection circuit wasn't a complete POS. I tried a search on CT Sounds on the forum just couldnt find an answer. ![]() Now if I power on the amp it instantly goes into protect and starts popping and smoking. but the POS protect circuit did nothing as the amp was popping and smoking while it said it was in protect. I ran this amp for awhile, then it went into protect. What would be the best course of action?.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |